1000 Welcome to the InControl Tools 95 Monitor Wizard. 1001 1002 You have chosen to use the Monitor wizard because 1003 the manufacturer and model of your monitor is not 1004 among those listed in the Control Panel. 1005 1006 You may find the list in the Control Panel on the 1007 'Settings' page by pressing the 'Change Display Type...' 1008 button. 1009 1010 1011 If you are ready to begin click Next. 1012 1013 1040 In order to determine your monitor's capabilities we are 1041 going to apply various operating settings to your monitor. 1042 Each setting will cause your screen to flicker momentarily. 1043 When the test is done your original settings will be restored. 1044 1045 If you have never been through this process we 1046 recommend the 'Minimal' or 'Full' monitor setup, 1047 otherwise choose 'Custom'. 1048 1050 Determines which modes your monitor 1051 supports at a refresh rate of 60 Hz. 1053 Determines which modes your monitor 1054 supports at the highest refresh rate. 1056 Allows you to select your own mode 1057 and refresh rate combination. 1059 Please test this mode 1061 Mode tested and is valid 1063 Mode tested and is NOT valid 1080 You may begin testing when you are ready. The screen may 1081 flicker momentarily for each setting. The Wizard will ask 1082 you if the screen looks normal. If it doesn't look normal 1083 you can wait a moment or press the ESC key and your 1084 screen will be restored. 1085 1086 1120 You may begin testing when you are ready. The screen may 1121 flicker momentarily for each setting. The Wizard will ask 1122 you if the screen looks normal. If it doesn't look normal 1123 you can wait a moment or press the ESC key and your 1124 screen will be restored. 1125 1126 1160 You may select the modes to be tested( either one at a 1161 time or several at once). When you begin testing the 1162 Wizard will ask you if the screen looks normal. If it 1163 doesn't you can wait a moment or press the ESC key 1164 and your screen will be restored. 1165 1166 1200 The modes which your monitor can do have been collected. 1201 If you are satisfied with the test process and would like 1202 to save the results click 'Finish'. 1203 1204 If you would like to go back and perform the test again 1205 you may do so now. 1206 1207 1208 1240 There was no response to the previous mode. This probably \n 1241 means your monitor does not support this mode. Before \n 1242 continuing we wanted to protect your monitor by restoring \n 1243 it to its normal operating settings. \n \n 1244 Do you wish to continue testing? 1245 1246 1280 Does the Screen look Normal and Stable? \n \nPress 'ESC' or 'Cancel' to abort the test. \n 1281 Testing Mode: 1282 Diamond Custom Monitor Wizard - Welcome 1283 Diamond Custom Monitor Wizard - Setup Type 1284 Diamond Custom Monitor Wizard - Minimal Setup 1285 Diamond Custom Monitor Wizard - Full Setup 1286 Diamond Custom Monitor Wizard - Custom Setup 1287 Diamond Custom Monitor Wizard - Finished 1288 Minimal 1289 Full 1290 Custom 1291 Begin Testing 1292 Clear results and start over. 1293 Legend 1294 Monitor Wizard - User defined monitor not selected 1295 Yes, I have my monitor owner's manual. 1296 Diamond Custom Monitor Wizard - Owner's Manual 1297 Horizontal [ kHz ] 1298 Vertical [ Hz ] 1299 Maximum Frequencies 1300 Test Next Mode 1301 %d %% Completed 1302 This mode will not be tested since it exceeds at least \n 1303 one of the limits specified in your Monitor's owner manual. 1304 Diamond Custom Monitor Wizard - Disclaimer 1340 In order to run the Custom Monitor Wizard you must first \n 1341 select '(User defined monitor types)' in the Control Panel. \n 1342 \n 1343 To make this selection do the following: \n 1344 \n 1345 1. Enter the Control Panel. \n 1346 2. Click the 'Settings' tab. \n 1347 3. Click the 'Change Display Type...' button. \n 1348 4. Click the 'Change' Monitor type button. \n 1349 5. Click the 'Show all devices' option. \n 1350 6. Click the '(User defined monitor types)' entry. \n 1351 7. Click 'OK' \n 1352 8. Click 'Close' button. \n 1353 \n 1354 You can now run the Monitor Wizard \n 1380 Please enter the maximum horizontal frequency in kHz. 1381 and the maximum vertical frequecy in Hz. If your 1382 manual does not have this information, don't worry, 1383 you can still use the Monitor wizard. 1384 1400 Now select the maximum resolution which your monitor 1401 can support. When you are ready to continue click Next. 1440 Please be aware that during the subsequent test 1441 we may be applying electrical signals to your 1442 monitor for which it was not designed. Although 1443 the ESC key will terminate the test immediately 1444 there is a small risk of damage to your monitor. 1445 1446 1447 Your monitor owner's manual will be useful during 1448 this process. However, if you don't have it don't worry. 1449 We will just work a little harder for you. 1450 1451 1452 If you are ready to begin click Next. 1453 61440 Open 61441 Save As 61442 All Files (*.*) 61443 Untitled 61696 Invalid filename. 61697 Failed to open document. 61698 Failed to save document. 61699 Save changes to %1? 61700 Failed to create empty document. 61701 The file is too large to open. 61702 Could not start print job. 61703 Failed to launch help. 61704 Internal application error. 61705 Command failed. 61706 Insufficient memory to perform operation. 61712 Please enter an integer. 61713 Please enter a number. 61714 Please enter an integer between %1 and %2. 61715 Please enter a number between %1 and %2. 61716 Please enter no more than %1 characters. 61717 Please select a button. 61718 Please enter an integer between 0 and 255. 61719 Please enter a positive integer. 61728 Unexpected file format. 61729 %1\nCannot find this file.\nPlease verify that the correct path and file name are given. 61730 Destination disk drive is full. 61731 Unable to read from %1, it is opened by someone else. 61732 Unable to write to %1, it is read-only or opened by someone else. 61733 An unexpected error occurred while reading %1. 61734 An unexpected error occurred while writing %1. 61836 Unable to read write-only property. 61837 Unable to write read-only property. 61840 Unable to load mail system support. 61841 Mail system DLL is invalid. 61842 Send Mail failed to send message. 61984 OK\n50 61985 Cancel\n50 61986 &Apply\n50 61987 &Help\n50 61988 Close